molding temperature

The study shows that the molding temperature is decided according to the molding pressure .

结果表明：成型温度的确定决定于成型压力。

The results showed that the main factors affecting mechanical properties of the composite materials were the carbon fibers content and molding temperature .

研究表明，影响复合材料机械性能的主要因素是碳纤维含量和成型温度。

Numerical Simulation of Pile Foundation Conduction at Different Molding Temperature in Permafrost Regions

多年冻土地区不同入模温度下桩基温度场数值分析

Effect of molding temperature on structure and properties of poly-1-butylene thermoplastic elastomer

模压温度对聚1-丁烯热塑性弹性体结构及性能的影响

In addition , the influence of molding temperature and injection pressure on PS product was discussed , too .

另外，也研究了模温和熔体压力对PS注塑制品的影响。

The optimal molding temperature and pressure of their composite are 140C and 7.3 MPa .

麻纤维复合材料的最佳成型温度为140℃，成型压力7.3MPa。

The raw materials , extrusion pressure , pressure holding time and molding temperature during extrusion moulding have great effects on the quality of products .

挤压成型过程中原材料、挤压力、保压时间和成型温度对制品的品质影响较大。

The results showed that the morphology of dispersed TLCP phase and the mechanical properties of the materials were strongly dependent on molding temperature .

结果表明，注射成型温度对最终复合材料中TLCP形态及材料的力学性能有明显的影响。

The best performance of camber polymer lithium ion battery was got at the molding temperature of130 ℃ with self-made molding device .

研究结果表明，利用设计的模具，130℃条件下，具有最好的成型效果。

The TLCP fibrils in the composites appeared somewhat retracted when the molding temperature was 260 ℃ .

注射成型温度为240℃时，复合材料中TLCP相开始出现熔融回缩；

And the molding temperature , the molding time and the content of BMI had tremendous effect on the mechanical properties of the finial elastomers .

成型温度、时间和BMI的含量会对胶粉弹性体的力学性能产生显著影响。

Further , the influence of processing parameters ( including molding temperature , pressure , loading time and loading procedures , etc. ) on the mechanical properties of composite laminates was investigated .

基于其分析结果，考察了模压成型温度、压力、时间和加载方式等工艺参数对复合材料层压板力学性能的影响，并初步探讨了这些因素对材料结构与性能的调控机制。

In this paper , the integration of foundation pile conduction , frozen soil , air temperature , concrete hydrate heat , concrete molding temperature is considered to establish a numerical simulation .

考虑基桩传热、地基冻土、大气温度变化、混凝土中水泥水化热、混凝土入模温度变化及其相互作用，建立温度场数值分析模型。

In the molding temperature of180 ℃, CB as reinforcement , ABS as matrix , using hot molding press to produce CB / ABS composite material laminates .

在成型温度180℃下，以碳布为增强体、ABS为基体，采用模压成型，生产出CB/ABS复合材料层压板。

The semi-solid forming technology has been considered to be one of the most advanced metal forming technology , which is characterized by easy to near-net shape , low molding temperature , and energy conservation .

半固态成形技术被认为是一种最具先进性的金属成形加工技术，其特点是易于近终成形、成形温度低、节约能源等。

The result showed that , the influence of injection molding temperature on various properties of Cu / LDPE composites was quite complex , and 170 ℃ was selected as the best injection molding temperature by comprehensive consideration .

研究表明，注塑温度对Cu/LDPE复合材料的各方面性能影响比较复杂，综合评价选定170℃为最佳注塑温度。

This model takes the molding temperature and mixture ratio of straw and rice bran as the control parameters of compression molding process . It also takes molding fuel durability , relaxation density and fuel heating value as the evaluation parameters .

以稻草与米糠的混合比例和成型温度作为压缩成型过程的控制参数，以成型燃料的抗跌碎性、松弛密度和燃料热值作为压缩成型过程的评价参数。

Pore forming mechanism is researched for the RTM process . The impact of fiber spacing , the molding temperature and filling velocity on the flow front are showed . ( 2 ) The reinforcing material is changed to porous medium .

对RTM工艺过程中孔隙形成机理进行研究，得到纤维束间距、成型温度、填充速度等参数对流动前沿的影响。

The optimum conditions of the composite materials forming process were determined : the molding temperature was 160 ℃; the molding pressure was 12 MPa ; the holding time was 30 min ; In composite materials , carbon fibers content was 4 % .

正交试验确定了复合材料最佳成型工艺条件：成型温度为160℃；成型压力为12MPa；保压时间为30min；复合材料中碳纤维含量为4%。

The 4 factors , such as specific absorption of aggregate , dosage of fiber , dosage of cement and molding temperature , were assembled properly by orthogonal design method , the effects of the factors on the optimum proportion of asphalt were studied at the same time .

采用正交试验方法分析集料吸水率、纤维用量、水泥掺量及成型温度这4个因素对沥青混合料最佳油石比的影响程度。

It is also indicated by the experimentation of process parameters that much better properties of friction and wear are achieved for warm-press friction materials at the conditions of the molding temperature 110 ~ 120 ℃, the pressure 15 ~ 35MPa and the holding time 1 ~ 2 minutes .

工艺参数研究表明：模压温度110～120℃、成型压力15～35MPa、保压时间1～2min，制备的材料具有较高冲击强度和优良的摩擦磨损性能。

Temperature Calculation Method Based on Molding Compound Temperature Measurement

以塑封料温度测量为基础的一种结温计算方法

Study on Injection Molding Melt Temperature

注塑成型熔体温度的研究

The construction plan that is adopted to ensure concrete winter construction quality and technology measures are expounded from the aspect of how to control getting out of tank 's temperature of concrete , molding 's temperature and pumping 's temperature of concrete .

论述了通过控制混凝土出罐温度、成型温度和入模温度来确保冬施混凝土施工质量的施工方案和技术措施。

The need of high-gloss injection molding for quick temperature rising and drop cannot be met .

无法满足高光注塑中快速升温及快速降温的需要。

Meanwhile temperature is one of the most important parameters in injection molding process . Temperature parameter will not only influence cycle time but also result in quality problems .

温度是注塑成型工艺中最重要的参数之一，不合理的温度参数会影响塑件的成型周期和制品品质。

The process control technologies of polymer injection molding , including temperature control , pressure control and speed control , are discussed . The development trend of this process control system is expounded .

分析聚合物注射成型过程中温度控制、压力控制、速度控制的技术现状，揭示了注射成型过程控制系统的发展前景。

The cooling process plays an important role in the quality and performance of the products in injection molding , The temperature is the most important process parameters in injection cooling process .

注射成型的冷却过程对最终成型制品的质量、性能起着至关重要的作用。

Blending a small amount of bituminous coal and anthracite in the organic binder by kneading , molding , carbonization temperature indicators available to meet the coke product .

将少量烟煤配入无烟煤中与有机粘接剂经混捏、成型、高温炭化后可得到符合指标的型焦产品。

The molding pressure and temperature are two key factors that influence the molding process , which have great effects on the thickness , density , permeability and in-plane electrical resistance of the carbon paper .

采用浸渍模压工艺制备炭纸时，模压压力和模压温度是影响模压工艺的重要因素，对炭纸的厚度、密度、气体渗透速度、面电阻率都有显著的影响。